RC SERIES
Item | Unit | Can work as a lathe | Horizontal | Two D.D. Motors: 2000 RPM Can Work as aLathe | Two D.D. Motors: 2000 RPM Can Work as a Lathe | |||
---|---|---|---|---|---|---|---|---|
AD-250HS | HAD-210F-HS | FAD-170F-HS | FAD-210F-HS | FAD-300F-HS | ||||
Table Diameter | mm | Ø250 | Ø210 | Ø170 | Ø210 | Ø300 | ||
Diameter of Table Central Hole | mm | Ø50H7 x 5.5 deep | Ø40H7 x 12 deep | Ø40h7 x 12 deep | Ø25H7 x 12 deep | |||
Inner Diameter of Mandrel Sleeve | mm | – | – | – | – | |||
Diameter of Center Through Hole | mm | – | – | – | – | |||
Center Height (Vertical) | mm | 200 | – | – | – | |||
Table Height (Horizontal) | mm | 335 | 240 | 290 | 385 | |||
Table T-slot Width | mm | – | – | – | 14H7 | |||
Guide Block Width | mm | – | 14h7 | 18h7 | 14h7 | |||
Axis | – | – | – | Rotary axis | Tilt axis ±100˚ | Rotary axis | Tilt axis ±100˚ | |
Cooling System | – | Water Cooling | Water Cooling | Water Cooling | Free Cooling | Water Cooling | Water Cooling | |
Transmission Mechanism | – | D.D. Motor | D.D. Motor | D.D. Motor | D.D. Motor | D.D. Motor | D.D. Motor | |
Min. Increment | deg. | 0.001 | 0.001 | 0.001 | 0.001 | 0.001 | 0.001 | |
Indexing Precision (while tilt 0° ~+90˚ | sec. | 20 | 20 | 20 | 30 | 20 | 20 | |
Repeatability | sec. | 4 | 4 | 4 | 8 | 4 | 8 | |
Clamping System (Pneumatic) | kg/cm2 | 6 | 6 | 6 | 6 | |||
Clamping Torque | Nm | 450 (Powerful) | 310 | 310 | 500 | 430 | 730 | |
Servo Motor Model | FANUC | DD Motor | DD Motor | DD Motor | DD Motor | |||
MITSUBISHI | ||||||||
Speed Reduction Ratio | – | Direct Drive | Direct Drive | Direct Drive | Direct Drive | Direct Drive | Direct Drive | |
Rated / Max. Speed | r.p.m | 1100/2000 | 1900/2880 | 1900/2880 | 150/200 | 818/2000 | 50/- | |
Rated / Max. Cutting Torque | Nm | 113/169 | 48/- | 48/- | 48/(Water Cooling 118) | 113/- | 554/741 | |
Allowable Inertia Load Capacity (Horizontal) | kg ∙ cm / sec2 | 3.1 | – | – | – | |||
Allowable Workpiece Load (dyamic) |
0º Horizontal | kg | Please refer to the manual | |||||
0º~90º Tilt | kg | |||||||
Allowable Load (with clamping) |
F | N | 10000 | 4000 | 4000 | – | ||
FxL | Nm | 1150 | 500 | 500 | 730 | |||
FxL | Nm | 550 | 310 | 500 | 430 | |||
Net Weight (D.D. motor included) | kg | 158 | – | – | 730 | |||
Electrical Specification | ||||||||
Encoder | – | Subject to demand and controller | ||||||
Voltage (Back E.M.F) | Vrms/100rpm | 33 | 14.2 | Rotary axis: 14.2 | Rotary axis: 33 | |||
Rotor Poles | – | 22 | 22 | 22 | 22 | |||
Rated / Max. Current | Arms | 26.5/50.2 | 26.1 | 26.1 | 26.5/50.2 | |||
Power Rating | KW | 9.9 | 9.7 | 9.7 | 0.76 | 9.9/2.11 |